Operators should note that the revision level and date on the above P/N's do not matter with regard to the applicability of paragraph (e) of this AD. Therefore, we have revised the applicability of paragraph (e) of this AD to exclude certain affected Model MD11 airplanes equipped with the ECU's listed above installed. Operators of affected Model MD11 airplanes equipped with a future ECU in production (approved after the publication of the AD) may request an alternative method of compliance with this AD under the provisions of paragraph (j) of the final rule.

Request to Include An Optional Terminating Action

One commenter requests that the proposed AD be revised to include an optional terminating action for the repetitive detailed visual inspection and functional checks to detect failed open pressure switches on the hydraulic control unit required by paragraph (h) of the proposed AD. The commenter states that the procedures identified in Boeing MD11 CMR, Report Number MDCK4174, Revision P, dated April 5, 1999; McDonnell Douglas Service Bulletin MD1131085, Revision 01, dated April 9, 1998; and McDonnell Douglas Service Bulletin MD1178 007, dated January 31, 2000; eliminate the need for the repetitive inspections and functional
[[Page 15787]]
checks of the pressure switch and wiring of the hydraulic control unit.

The FAA does not agree. No technical justification, criteria, or data were submitted to support the commenter's request. At this time, the FAA cannot determine whether the commenter's request is applicable. However, the FAA may approve requests for an alternative method of compliance under the provisions of paragraph (j) of this AD if sufficient data are submitted to substantiate that such a design change would provide an acceptable level of safety.

Request to Revise Descriptive Language

One commenter notes that a sentence under the heading ``Explanation of Relevant Service Information'' reads ``These procedures also include inspections to detect failed open pressure switches on the hydraulic control unit, failed stow position microswitches, or failed locking mechanisms.'' The commenter also notes that paragraph (h) of the proposed AD reads ``* * * to detect failed stow position
microswitches.'' The commenter requests that the phrase ``and their associated wiring'' be inserted after the word ``microswitches'' in both places in the proposed AD.

The FAA agrees that the commenter's suggestion is a more accurate description of the inspection area. We have revised paragraph (h) of the final rule accordingly. The ``Explanation of Relevant Service Information'' section of the proposed AD does not reappear in the final rule.

Request to Mandate Reporting

One commenter requests that the proposed AD require operators to submit to Boeing the inspection record (i.e., Attachment A) in McDonnell Douglas Alert Service Bulletin DC1078A056, Revision 02, dated February 18, 1999, and McDonnell Douglas Alert Service Bulletin DC1078A057, Revision 01, dated February 18, 1999, for the applicable initial inspections required by the proposed AD. Reports from subsequent inspections should be at an operator's discretion. The commenter states that the data obtained from the reports would enhance the reliability database for the DC10 thrust reverser system.

The FAA does not agree. The FAA finds it appropriate to leave it to the operators' discretion to report inspection findings to Boeing. Since the suggested change would alter the actions currently required by this AD, additional rulemaking would be required. The FAA finds that to delay this action would be inappropriate in light of the identified unsafe condition. No change to this final rule is necessary. Requests to Revise Cost Impact

One commenter notes that, under the heading ``Cost Impact,'' the proposed AD states that, for McDonnell Douglas Model DC1010, 15, 30, and 40 series airplanes and KC10A (military) airplanes that are listed in McDonnell Douglas Alert Service Bulletin DC1078A056, Revision 02, dated February 18, 1999, it would take approximately 5 work hours per airplane to accomplish the required actions related to this service bulletin. The commenter states that the proposed actions will take approximately 16 work hours per engine or 48 work hours per airplane. The commenter also states that maintenance access for the No. 2 engine on the subject airplanes requires specific stand access. Another commenter states that these proposed actions will take approximately 26 work hours per airplane to accomplish and five hours to do the actions specified in McDonnell Douglas Alert Service Bulletin DC1078A056, Revision 02, and 21 work hours to do the actions specified in Middle River Aircraft Systems (MRAS) CF606 Service Bulletin S/B 78 2004, Revision 1, dated December 18, 1997, or MRAS CF650 Service Bulletin S/B 783001, Revision 2, dated December 18, 1997.

One commenter states that, for Model MD11 airplanes equipped with General Electric (GE) or Pratt & Whitney (P&W) engines, the proposed actions will take approximately 10 work hours per airplane. Under the heading ``Cost Impact,'' the proposed AD indicates 6 work hours per airplane equipped with GE engines and 31 work hours per airplane equipped with P&W engines.

After considering the information presented by commenters, the FAA agrees that the subject work hours in the cost impact information, below, should be revised. We have revised the work hours in the final rule as suggested by the commenters. The economic analysis, however, is limited only to the cost of actions actually required by the rule. It does not consider the costs of ``on condition actions, e.g., repair, if necessary,'' since those actions would be required to be accomplished, regardless of AD direction, in order to correct an unsafe condition identified in an airplane and to ensure operation of that airplane in an airworthy condition, as required by the Federal Aviation Regulations.

One commenter states that, for Model DC1040 series airplanes that are listed in McDonnell Douglas Alert Service Bulletin DC1078A057, Revision 01, dated February 18, 1999, the proposed actions will take 48 work hours per airplane, rather than the 31 work hours specified under the heading ``Cost Impact.''

The FAA does not agree. The cost impact information, below, describes only the ``direct'' costs of the specific actions required by this AD. The number of work hours necessary to accomplish the required actions, specified as 31 in the cost impact information, below, was provided by the manufacturer in McDonnell Douglas Alert Service Bulletin DC1078A057, Revision 01, as the best data available to date. This number represents the time necessary to perform only the actions actually required by this AD. The FAA recognizes that, in accomplishing the requirements of any AD, operators may incur ``incidental'' costs in addition to the ``direct'' costs. The cost analysis in AD rulemaking actions, however, typically does not include incidental costs, such as the time required to gain access and close up; planning time; or time necessitated by other administrative actions. Because incidental costs may vary significantly from operator to operator, they are almost impossible to calculate.

One commenter notes that, under the heading ``Cost Impact,'' the proposed AD states that five McDonnell Model MD11 airplanes equipped with P&W engines of U.S. registry would be affected by the proposed AD. The commenter states that it has 15 affected airplanes. Another commenter states that the number of McDonnell Douglas Model MD11 airplanes equipped with GE engines of U.S. Registry that would be affected by the proposed AD is also incorrect; the correct number is approximately 81 (not including hull losses). From these comments, the FAA infers that the commenters are requesting that the number of airplanes be revised in the appropriate sentence under the heading ``Cost Impact.''

The FAA agrees with the commenters to update the number of affected airplanes. However, we have confirmed with operators that there are 110 Model MD11 airplanes of the affected design in the worldwide fleet that are equipped with GE engines, of which, 85 are on the U.S. registry. There are 81 Model MD11 airplanes of the affected design in the worldwide fleet that are equipped with P&W engines, of which, 29 are on the U.S. registry. Therefore, we have revised the final rule accordingly.

One commenter requests that, in the second paragraph under the heading ``Cost Impact'' and paragraph (b), ``40'' be deleted in the first sentence. The commenter states that McDonnell Douglas Alert Service Bulletin DC10
[[Page 15788]]
78A056, Revision 02, dated February 18, 1999 (which is referenced in that paragraph as the appropriate source of service information for determining the affected airplanes), is only applicable to those affected models equipped with GE engines. Model DC1040 series airplanes are powered by P&W engines. The FAA agrees and has revised the final rule accordingly.

Explanation of Changes Made to Proposed AD

For clarification purposes, the FAA has revised the reference to the Boeing MD11 CMR to include its associated Report Number MDCK4174. The proposed AD referenced the incorrect date of the original version of McDonnell Douglas Alert Service Bulletin DC1078A056. We have revised the date of that service bulletin from January 1, 1998, to January 19, 1998, in the final rule. In addition, we have made some minor editorial changes to the body of the AD to incorporate the use of plain language.

Conclusion

After careful review of the available data, including the comments noted above, the FAA has determined that air safety and the public interest require the adoption of the rule with the changes previously described. The FAA has determined that these changes will neither increase the economic burden on any operator nor increase the scope of the AD.

Interim Action

For all Model DC10 series airplanes, this is considered to be interim action. The manufacturer has advised that it currently is developing a modification that will positively address the unsafe condition addressed by this AD. Once this modification is developed, approved, and available, the FAA may consider additional rulemaking. Cost Impact

There are approximately 259 Model DC1010, 30, and 40 series airplanes and KC10A (military) airplanes of the affected design in the worldwide fleet that are listed in McDonnell Douglas DC10 Service Bulletin 7840, Revision 1, dated July 24, 1979. The FAA estimates that 135 airplanes of U.S. registry will be affected by this AD, that it will take approximately 10 work hours per airplane to accomplish the required actions related to this service bulletin, and that the average labor rate is $60 per work hour. The required parts will be obtained from the operator's stock. Based on these figures, the cost impact of this portion of the AD on U.S. operators is estimated to be $81,000, or $600 per airplane.

There are approximately 359 Model DC1010, 15, and 30 series airplanes and KC10A (military) airplanes of the affected design in the worldwide fleet that are listed in McDonnell Douglas Alert Service Bulletin DC1078A056, Revision 02, dated February 18, 1999. The FAA estimates that 187 airplanes of U.S. registry will be affected by this AD, that it will take approximately 26 work hours per airplane to accomplish the required actions related to this service bulletin, and that the average labor rate is $60 per work hour. Based on these figures, the cost impact of this portion of the AD on U.S. operators is estimated to be $291,720, or $1,560 per airplane, per inspection cycle.

There are approximately 41 Model DC1040 series airplanes of the affected design in the worldwide fleet that are listed in McDonnell Douglas Alert Service Bulletin DC1078A057, Revision 01, dated February 18, 1999. The FAA estimates that 22 airplanes of U.S. registry will be affected by this AD, that it will take approximately 31 work hours per airplane to accomplish the required actions related to this service bulletin, and that the average labor rate is $60 per work hour. Based on these figures, the cost impact of this portion of the AD on U.S. operators is estimated to be $40,920, or $1,860 per airplane, per inspection cycle.

There are approximately 110 Model MD11 airplanes of the affected design in the worldwide fleet that are equipped with GE engines. The FAA estimates that 85 airplanes of U.S. registry will be affected by this AD, that it will take approximately 10 work hours per airplane to accomplish the required actions, and that the average labor rate is $60 per work hour. Based on these figures, the cost impact of this portion of the AD on U.S. operators is estimated to be $51,000, or $600 per airplane, per inspection cycle.

There are approximately 81 Model MD11 airplanes of the affected design in the worldwide fleet that are equipped with P&W engines. The FAA estimates that 29 airplanes of U.S. registry will be affected by this AD, that it will take approximately 10 work hours per airplane to accomplish the required actions, and that the average labor rate is $60 per work hour. Based on these figures, the cost impact of this portion of the AD on U.S. operators is estimated to be $17,400, or $600 per airplane, per inspection cycle.

The cost impact figures discussed above are based on assumptions that no operator has yet accomplished any of the requirements of this AD action, and that no operator would accomplish those actions in the future if this AD were not adopted. The cost impact figures discussed in AD rulemaking actions represent only the time necessary to perform the specific actions actually required by the AD. These figures typically do not include incidental costs, such as the time required to gain access and close up, planning time, or time necessitated by other administrative actions.

Regulatory Impact

The regulations adopted herein will not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this final rule does not have federalism implications under Executive Order 13132.

For the reasons discussed above, I certify that this action (1) is not a ``significant regulatory action'' under Executive Order 12866; (2) is not a ``significant rule'' under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A final evaluation has been prepared for this action and it is contained in the Rules Docket. A copy of it may be obtained from the Rules Docket at the location provided under the caption ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows: PART 39AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by adding the following new airworthiness directive:
20010510 McDonnell Douglas: Amendment 3912147. Docket 99NM108 AD.

[[Page 15789]]

Applicability: All Model DC10 series airplanes, MD11 series airplanes, and KC10A (military) airplanes; certificated in any category.

Note 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the
requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (j) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it.

Compliance: Required as indicated, unless accomplished previously.

To prevent unwanted deployment of the thrust reverser, which could result in reduced controllability of the airplane, accomplish the following:
Modification of Certain Model DC10 Series Airplanes
(a) For Model DC1010, 30, and 40 series airplanes listed in McDonnell Douglas DC10 Service Bulletin 7840, Revision 1, dated July 24, 1979: Within 3,000 flight hours or 12 months after the effective date of this AD, whichever occurs first, install a thrust reverser interlock (inflight lockout) by installing two relays on the forward relay panel and revising the associated wiring, per the service bulletin. The requirements of this paragraph must be done before or with the requirements of paragraph (b) or (c) of this AD, as applicable.
Inspection of Model DC10 Airplanes Powered by General Electric Engines (b) For DC1010, 15, and 30 series airplanes listed in
McDonnell Douglas Alert Service Bulletin DC1078A056, Revision 02, dated February 18, 1999: Within 3,000 flight hours or 12 months after the effective date of this AD, whichever occurs first, do a detailed visual inspection, functional check, and torque checks of the thrust reverser system and the thrust reverser interlocks to detect discrepancies [i.e., below minimum torque required to overcome the pneumatic drive motor (PDM) disc brake; cuts, tears, or missing sections of the translating cowl seals; dents, cracks, holes, or loose fasteners on the Dagmar fairing or aft frame; improper alignment of the feedback rod; hidden faults in the translating cowl auto restow system; a failed over pressure shutoff valve (OPSOV); and improper operation of the fan reverser actuation system], per the service bulletin. Repeat the inspections thereafter every 6,000 flight hours or 18 months, whichever occurs first.

Note 2: For the purposes of this AD, a detailed visual inspection is defined as: ``An intensive visual examination of a specific structural area, system, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at intensity deemed appropriate by the inspector. Inspection aids such as mirror, magnifying lenses, etc., may be used. Surface cleaning and elaborate access procedures may be required.''

Note 3: Inspection of the thrust reverser system accomplished before the effective date of this AD per McDonnell Douglas Alert Service Bulletin DC1078A056, dated January 19, 1998, or Revision 01, dated June 4, 1998, is considered acceptable for compliance with the initial inspections required by paragraph (b) of this AD.

Note 4: McDonnell Douglas Alert Service Bulletin DC1078A056, Revision 02, dated February 18, 1999, references Middle River Aircraft Systems (MRAS) Service Bulletin 783001, Revision 2, dated December 18, 1997, and MRAS Service Bulletin 782004, Revision 1, dated December 18, 1997, as additional sources of service
information for accomplishment of the inspections and corrective actions.
Inspection of Model DC1040 Series Airplanes Powered by Pratt & Whitney Engines
(c) For Model DC1040 series airplanes listed in McDonnell Douglas Alert Service Bulletin DC1078A057, Revision 01, dated February 18, 1999: Within 3,000 flight hours or 12 months after the effective date of this AD, whichever occurs first, do a detailed visual inspection, functional check, and torque checks of the thrust reverser system to detect discrepancies [i.e. damaged or improperly functioning stow latch hooks; cuts, gouges, and holes in the pneumatic seal/bullnose seal; improper functioning of the pneumatic drive unit (PDU) position locking retention feature; improper installation or improper operation of the system wiring, switches, or indicator lights; damage to the fan reverser flexshafts, actuators, translating sleeve tracks, or sliders; improper function of the inflight interlock system; and improper operation of the thrust reverser power source, translating sleeve, throttle interlocks, or cockpit indicators], per the service bulletin. Repeat the inspections thereafter every 6,000 flight hours or 18 months, whichever occurs first.

Note 5: Inspection of the thrust reverser system per McDonnell Douglas Alert Service Bulletin DC1078A057, dated November 30, 1998, accomplished before the effective date of this AD, is considered acceptable for initial compliance with the applicable action specified in paragraph (c) of this AD.
Inspection of Model MD11 Series Airplanes Powered by General Electric Engines
(d) For Model MD11 series airplanes equipped with General Electric engines: Do a detailed visual inspection and functional check of the two position microswitches on the Center Drive Unit (CDU) and their associated wiring to detect failed open switches or open wire runs, and the aerodynamic seal between the reverser translating sleeves and the main reverser structure to detect damage to the aerodynamic seal or its interface surface on the reverser structure; and do an inspection to determine the torque value of the cone brake within the CDU to detect slipping or a failed CDU brake. These inspections and the functional check shall be done per pages 17 and 18 of the Boeing MD11 Certification Maintenance Requirements (CMR), Report Number MDCK4174, Revision P, dated April 5, 1999, or Revision Q, dated December 22, 1999; at the times specified in paragraph (d)(1) or (d)(2) of this AD, as applicable.
(1) For airplanes on which the modification (i.e., translating cowl double Pseal configuration) specified in MRAS CF680C2D1F Alert Service Bulletin 78A1005, dated March 29, 1995; Revision 1, dated June 6, 1996; Revision 2, dated October 18, 1996; Revision 3, dated August 18, 1997; or Revision 4, dated December 21, 1998; has been accomplished: Inspect within 7,000 flight hours after the effective date of this AD. Repeat the inspections thereafter every 7,000 flight hours.
(2) For airplanes on which the modification (i.e., translating cowl double Pseal configuration) specified in MRAS Service Bulletin 78A1005, dated March 29, 1995; Revision 1, dated June 6, 1996; Revision 2, dated October 18, 1996; Revision 3, dated August 18, 1997; or Revision 4, dated December 21, 1998; has not been accomplished: Inspect within 2,000 flight hours after the effective date of this AD. Repeat the inspections thereafter every 2,000 flight hours.

Note 6: The type certificate for these airplanes includes a CMR to perform this same inspection at intervals not to exceed 17,000 flight hours. This CMR is still in effect and must be complied with. If the CMR requires an inspection before the compliance time stated in paragraph (d)(1) or (d)(2) of the AD, as applicable, operators may take credit for doing the CMR, and then repeat the inspection at the intervals specified in that applicable paragraph.
(e) For Model MD11 series airplanes equipped with General Electric engines, without an electronic control unit (ECU) listed in Table 1 installed: Within 2,000 flight hours after the effective date of this AD, test the thrust reverser pressurization system to detect an uncommanded pressurized thrust reverser system and/or a failed thrust reverser pressure switch, as applicable, per pages 52 and 53 of the Boeing MD11 CMR, Report Number MDCK4174, Revision P, dated April 5, 1999. Repeat the inspections thereafter every 2,000 flight hours. Table 1 is as follows:
Table 1
ECU P/N
1519M91P06
1519M91P07
1519M91P09
1820M34P01
1820M34P02
1820M34P04
(f) For Model MD11 series airplanes equipped with General Electric engines: Within 7,000 flight hours after the effective date of this AD, inspect the thrust reverser inflight lockout system (IFLS) to detect failure
[[Page 15790]]
of the flight control computer (FCC), radio altimeter input to the FCC, main landing gear wheel speed input to the FCC, ground sensing system, or wiring that causes an onground status in the IFLS while the airplane is airborne, per page 54 of the Boeing MD11 CMR, Report Number MDCK4174, Revision P, dated April 5, 1999. Repeat the inspections thereafter every 7,000 flight hours.
(g) For Model MD11 series airplanes equipped with General Electric engines: Within 600 flight hours after the effective date of this AD, accomplish the actions specified in paragraph (g)(1), (g)(2), or (g)(3) of this AD per MRAS CF680C2D1F Alert Service Bulletin 78A1082, dated August 25, 1999.
(1) Perform a pressure differential inspection of the
directional pilot valves (DPV) to detect a partially open solenoid or failed Oring. If any partially open solenoid or failed Oring is detected, before further flight, replace the discrepant DPV with a DPV that has been inspected per this paragraph. Repeat the inspection thereafter every 2,000 flight hours. Or
(2) Replace the DPV with a DPV that has been inspected per paragraph (g)(1) of this AD. Repeat the replacement thereafter every 2,000 flight hours. Or
(3) Deactivate the thrust reverser per the MD11 Master Minimum Equipment List, and reactivate the thrust reverser only after accomplishing the actions specified in paragraph (g)(1) or (g)(2) of this AD.
Inspection of Model MD11 Series Airplanes Powered by Pratt & Whitney Engines
(h) For MD11 series airplanes equipped with Pratt & Whitney engines: Within 7,000 flight hours after the effective date of this AD, do a detailed visual inspection and functional checks, as applicable, of the thrust reverser system and the thrust reverser IFLS to detect failed open pressure switches on the hydraulic control unit, to detect failed stow position microswitches and associated wiring, or failed locking mechanisms; and failure of the FCC, radio altimeter input to the FCC, main landing gear wheel speed input to the FCC, ground sensing system, or wiring that causes an onground status in the IFLS while the aircraft is airborne, per pages 19, 20, and 54 of the Boeing MD11 CMR, Report Number MDC K4174, Revision P, dated April 5, 1999. Repeat the inspections thereafter every 7,000 flight hours.

Note 7: The type certificate for these airplanes includes a CMR to perform this same inspection at intervals not to exceed 13,800 flight hours. This CMR is still in effect and must be complied with. If the CMR requires an inspection before the compliance time stated in paragraph (h) of the AD, operators may take credit for doing the CMR, and then repeat the inspection at the intervals specified in that paragraph.
Corrective Actions
(i) If any discrepancy is detected during any inspection required by this AD, before further flight, do the actions specified in either paragraph (i)(1) or (i)(2) of this AD.
(1) Do the applicable corrective action per the following service documents:
(i) Chapter 78 of McDonnell Douglas DC10 Aircraft Maintenance Manual;
(ii) Chapter 78 of McDonnell Douglas DC10 Turn Around Fault Isolation Manual; Chapter 78 of General Electric Shop Manual; (iii) MRAS CF66 Service Bulletin 782004, Revision 1, dated December 18, 1997;
(iv) MRAS CF650 Service Bulletin 783001 Revision 2, dated December 18, 1997;
(v) McDonnell Douglas Alert Service Bulletin DC1078A056, dated January 19, 1998, Revision 01, dated June 4, 1998, or Revision 02, dated February 18, 1999;
(vi) McDonnell Douglas Alert Service Bulletin DC1078A057, dated November 30, 1998, or Revision 01, dated February 18, 1999; (vii) Chapter 78 of McDonnell Douglas MD11 Aircraft Maintenance Manual;
(viii) Chapter 78 of McDonnell Douglas MD11 Fault Isolation Manual; or
(ix) A method approved by the Manager, Los Angeles Aircraft Certification Office (ACO), FAA.
(2) Deactivate the thrust reverser in accordance with the DC10 Master Minimum Equipment List or the MD11 Master Minimum Equipment List, as applicable.
Alternative Methods of Compliance
(j) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, Los Angeles ACO, FAA. Operators shall submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, Los Angeles ACO.

Note 8: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the Los Angeles ACO.
Special Flight Permits
(k) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished.
Incorporation by Reference
(l) Except as provided by paragraphs (i)(1) and (i)(2) of this AD, the actions shall be done per the applicable service bulletins identified in Table 2, which contain the specified list of effective pages. Table 2 is as follows:
Table 2 Revision level shown on Document and date Page numbers page Date shown on page McDonnell Douglas DC10 Service 120................... 1...................... July 24, 1979. Bulletin 7840, Revision 1, July 24,
1979.
McDonnell Douglas Alert Service 115................... 02..................... February 18, 1999. Bulletin DC1078A056, Revision 02,
February 18, 1999.
Attachment A......................... 14.................... 02..................... February 18, 1999. McDonnell Douglas Alert Service 142................... 01..................... February 18, 1999. Bulletin DC1078A057, Revision 01,
February 18, 1999.
Attachment A......................... 14.................... 01..................... February 18, 1999. Boeing MD11 Certification List of Effective Pages P (Only indicated on April 5, 1999 (Only Maintenance Requirements, Report Pages LIST1 through the cover page; no indicated on the cover Number MDCK4174, Revision P, April LIST2. other page contains page; no other page of 5, 1999. this information). the document is dated). Boeing MD11 Certification List of Effective Pages Q (Only indicated on December 22, 1999 (Only Maintenance Requirements, Report Pages LIST1 through the cover page; no indicated on the cover Number MDCK4174, Revision Q, LIST2. other page contains page; no other page of December 22, 1999. this information). the document is dated). Middle River Aircraft Systems CF6 115................... Original............... August 25, 1999. 80C2D1F Alert Service Bulletin
78A1082, August 25, 1999.
[[Page 15791]]
Middle River Aircraft Systems CF66 136................... 1...................... December 18, 1997. Service Bulletin 782004, Revision
1, December 18, 1997.
Middle River Aircraft Systems CF650 143................... 2...................... December 18, 1997. Service Bulletin 783001, Revision
2, December 18, 1997.
McDonnell Douglas Alert Service 115................... Original............... January 19, 1998. Bulletin DC1078A056, January 19,
1998.
Attachment A......................... 14.................... Original............... December 17, 1997. McDonnell Douglas Alert Service 115................... 01..................... June 4, 1998. Bulletin DC1078A056, Revision 01,
June 4, 1998.
McDonnell Douglas Alert Service 141................... Original............... November 30, 1998. Bulletin DC1078A057, November 30,
1998.
Attachment A......................... 14.................... Original............... November 30, 1998. McDonnell Douglas Alert Service 142................... 01..................... February 18, 1999. Bulletin DC1078A057, Revision 01,
February 18, 1999.
Attachment A......................... 14.................... 01..................... February 18, 1999.

This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from Boeing Commercial Aircraft Group, Long Beach Division, 3855 Lakewood Boulevard, Long Beach, California 90846, Attention: Technical Publications Business Administration, Dept. C1L51 (260). Copies may be inspected at the FAA, 1601 Lind Avenue, SW., Renton, Washington; or at the FAA, Los Angeles Aircraft Certification Office, 3960 Paramount Boulevard, Lakewood, California; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC.
Effective Date
(m) This amendment becomes effective on April 25, 2001.

Issued in Renton, Washington, on March 7, 2001.
Vi L. Lipski,
Manager, Transport Airplane Directorate, Aircraft Certification Service.
[FR Doc. 016282 Filed 32001; 8:45 am] BILLING CODE 491013U

FOR FURTHER INFORMATION CONTACT

Philip Kush, Aerospace Engineer, Propulsion Branch, ANM140L, FAA, Los Angeles Aircraft Certification Office, 3960 Paramount Boulevard, Lakewood, California 907124137; telephone (562) 6275263; fax (562) 6275210.