Browse: Departments Dates Agencies
Docket ID: [Docket No. NM205; Special Conditions No. 25-01-05-SC]
SUBJECT CATEGORY: Special Conditions: Fairchild Dornier GmbH, Model 728-100; Sudden Engine Stoppage
DOCUMENT SUMMARY: This notice proposes special conditions for the Fairchild
Dornier GmbH Model 728100 airplane. This airplane will have a novel or
unusual design feature when compared to the state of technology
envisioned in the airworthiness standards for transport category
airplanes, associated with engine size and torque load which affects
sudden engine stoppage. The applicable airworthiness regulations do not
contain adequate or appropriate safety standards for this design
feature. These special conditions contain the additional safety
standards that the Administrator considers necessary to establish a
level of safety equivalent to that established by the existing airworthiness standards.
[[Page 8486]]
SUMMARY: Fairchild Dornier GmbH Model 728-100 airplane,
The FAA invites interested persons to participate in this rulemaking by submitting written comments, data, or views. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. We ask that you send us two copies of written comments.
We will file in the docket all comments we receive, as well as a report summarizing each substantive public contact with FAA personnel concerning these proposed special conditions. The docket is available for public inspection before and after the comment closing date. If you wish to review the docket in person, go to the address in the ADDRESSES section of this notice between 7:30 a.m. and 4 p.m., Monday through Friday, except Federal holidays.
We will consider all comments we receive on or before the closing date for comments. We will consider comments filed late if it is possible to do so without incurring expense or delay. We may change the proposed special conditions in light of the comments we receive.
If you want the FAA to acknowledge receipt of your comments on this proposal, include with your comments a preaddressed, stamped postcard on which the docket number appears. We will stamp the date on the postcard and mail it back to you.
On May 5, 1998, Fairchild Dornier GmbH applied for a type certificate for their new Model 728100 airplane. The Model 728100 airplane is a 7085 passenger twinengine regional jet with a maximum takeoff weight of 77,600 pounds.
Under the provisions of 14 CFR 21.17, Fairchild Dornier must show that the Model 728100 airplane meets the applicable provisions of part 25, as amended by Amendments 251 through 2596. Fairchild Dornier GmbH has also applied to extend the certification basis to include Amendments 2597, 2598, and 25104.
If the Administrator finds that the applicable airworthiness regulations (i.e., 14 CFR part 25) do not contain adequate or appropriate safety standards for the Model 728100 airplane because of a novel or unusual design feature, special conditions are prescribed under the provisions of Sec. 21.16.
Special conditions, as defined in 14 CFR 11.19, are issued in accordance with Sec. 11.38 and become part of the type certification basis in accordance with 14 CFR 21.17(a)(2). Special conditions are initially applicable to the model for which they are issued. Should the type certificate for that model be amended later to include any other model that incorporates the same novel or unusual design feature, the special conditions would also apply to the other model under the provisions of 14 CFR 21.101(a)(1).
In addition to the applicable airworthiness regulations and special conditions, the Model 728100 airplane must comply with the fuel vent and exhaust emission requirements of 14 CFR part 34 and the noise certification requirements of 14 CFR part 36, and the FAA must issue a finding of regulatory adequacy pursuant to section 611 of Public Law 92574, the ``Noise Control Act of 1972.''
The Fairchild Dornier GmbH Model 728100 airplane will incorporate novel or unusual design features involving engine size and torque load that affect sudden engine stoppage conditions. Fairchild Dornier GmbH proposes to treat the sudden engine stoppage condition resulting from structural failure as an ultimate load condition. Section 25.361(b)(1) of part 25 specifically defines the seizure torque load, resulting from structural failure, as a limit load condition.
The limit engine torque load imposed by sudden engine stoppage due to malfunction or structural failure (such as compressor jamming) has been a specific requirement for transport category airplanes since 1957. The size, configuration, and failure modes of jet engines have changed considerably from those envisioned when the engine seizure requirement of Sec. 25.361(b) was first adopted. Current engines are much larger and are now designed with large bypass fans capable of producing much larger torque loads if they become jammed. It is evident from service history that the frequency of occurrence of the most severe sudden engine stoppage events are rare.
Relative to the engine configurations that existed when the rule was developed in 1957, the present generation of engines are sufficiently different and novel to justify issuance of special conditions to establish appropriate design standards. The latest generation of jet engines are capable of producing, during failure, transient loads that are significantly higher and more complex than the generation of engines that were present when the existing standard was developed. Therefore, the FAA has determined that special conditions are needed for the Fairchild Dornier GmbH Model 728100 airplane.
In order to maintain the level of safety envisioned in Sec. 25.361(b), a more comprehensive criteria is needed for the new generation of high bypass engines. The proposed special conditions would distinguish between the more common seizure events and those rarer seizure events resulting from structural failures. For these rarer but severe seizure events, the proposed criteria could allow some deformation in the engine supporting structure (ultimate load design) in order to absorb the higher energy associated with the high bypass engines, while at the same time protecting the adjacent primary structure in the wing and fuselage by providing a higher safety factor. The criteria for the more severe events would no longer be a pure static torque load condition, but would account for the full spectrum of transient dynamic loads developed from the engine failure condition. Applicability
As discussed above, these special conditions are applicable to the
Fairchild Dornier GmbH Model 728100 airplane. Should Fairchild Dornier
apply at a later date for a change to the type certificate to include
another model incorporating the same novel or unusual design feature,
these special conditions would apply to that model as well under the
provisions of section 21.101(a)(1). Fairchild Dornier has submitted applications for certification
[[Page 8487]]
of both increased and reduced passenger capacity derivatives of the
Model 728100 airplane. These derivative models are designated the
Model 928100 airplane and the Model 528100 airplane, respectively. As
currently proposed, these derivative models share the same design
feature of a highbypass ratio fan jet engine as the Model 728100
airplane, and it is anticipated that they will be included in the applicability of these proposed special conditions.
This action affects only certain novel or unusual design features on the Fairchild Dornier GmbH Model 728100 airplane. It is not a rule of general applicability, and it affects only the applicant who applied to the FAA for approval of these features on the airplane.
Aircraft, Aviation safety, Reporting and recordkeeping requirements.
The authority citation for these special conditions is as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701, 44702, 44704. The Proposed Special Conditions
Accordingly, the Federal Aviation Administration (FAA) proposes the following special conditions as part of the type certification basis for Fairchild Dornier GmbH Model 728100 airplanes.
1. Sudden Engine Stoppage. In lieu of compliance with 14 CFR 25.361(b), the following special conditions apply:
a. For turbine engine installations, the engine mounts, pylons and
adjacent supporting airframe structure must be designed to withstand 1g
level flight loads acting simultaneously with the maximum limit torque loads imposed by each of the following:
(1) Sudden engine deceleration due to a malfunction which could result in a temporary loss of power or thrust.
b. For auxiliary power unit installations, the power unit mounts
and adjacent supporting airframe structure must be designed to
withstand 1g level flight loads acting simultaneously with the maximum limit torque loads imposed by the each of the following:
(1) Sudden auxiliary power unit deceleration due to malfunction or structural failure.
(2) The maximum acceleration of the auxiliary power unit.
c. For engine supporting structure, an ultimate loading condition
must be considered that combines 1g flight loads with the transient dynamic loads resulting from each of the following:
(1) The loss of any fan, compressor, or turbine blade.
(2) Where applicable to a specific engine design, and separately
from the conditions specified in paragraph 1.(c)(1), any other engine structural failure that results in higher loads.
d. The ultimate loads developed from the conditions specified in paragraphs (c)(1) and (c)(2) above are to be multiplied by a factor of 1.0 when applied to engine mounts and pylons and multiplied by a factor of 1.25 when applied to adjacent supporting airframe structure.
Issued in Renton, Washington, on February 13, 2002. Ali Bahrami,
Acting Manager, Transport Airplane Directorate, Aircraft Certification Service.
[FR Doc. 024411 Filed 22202; 8:45 am]
BILLING CODE 491013P
FOR FURTHER INFORMATION CONTACT Tom Groves, FAA, International Branch, ANM116, Transport Airplane Directorate, Aircraft Certification Service, 1601 Lind Avenue SW., Renton, Washington 980554056; telephone (425) 2271503; facsimile (425) 2271149.
14 CFR Part 39 40 CFR Part 52 14 CFR Part 71 33 CFR Part 165 50 CFR Part 679 47 CFR Part 73 26 CFR Part 1 40 CFR Part 180 33 CFR Part 117 50 CFR Part 17 44 CFR Part 67 50 CFR Part 648 14 CFR Part 97 33 CFR Part 100 40 CFR Part 63 50 CFR Part 622 44 CFR Part 65 50 CFR Part 660 26 CFR Part 301 39 CFR Part 111 40 CFR Part 300 6 CFR Part 5 40 CFR Part 271 47 CFR Part 64 40 CFR Parts 52 and 81 50 CFR Part 665 44 CFR Part 64 10 CFR Part 50 49 CFR Part 571 47 CFR Part 76