Browse: Departments   Dates   Agencies  

CFR Citation: 14 CFR Part 25

Docket ID: [Docket No. NM211; Notice No. 25-02-03-SC]

NOTICE: PROPOSED RULES

ACTION: Airworthiness standards:

DOCUMENT ACTION: Notice of proposed special conditions.

SUBJECT CATEGORY: Special Conditions: Airbus Industrie, Model A340-500/-600 Airplanes; Ground Loads and Conditions for Center Landing Gear With Four Wheels and Braking Capability

DATES: Comments must be received on or before April 19, 2002.

DOCUMENT SUMMARY: This action proposes special conditions for Airbus Industrie Model A340500 and 600 airplanes. These airplanes will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. This design feature is associated with the landing gear, in the form of a fourwheeled center landing gear, installed under the fuselage, which functions like a main landing gear in all respects, including the ability to brake. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

SUMMARY: Special conditions—; Airbus Industrie Model A340-500/-600 airplanes,

SUPPLEMENTAL INFORMATION

The FAA invites interested persons to participate in this rulemaking by submitting written comments, data, or views. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. We ask that you send us two copies of written comments.

We will file in the docket all comments we receive, as well as a report summarizing each substantive public contact with FAA personnel concerning these proposed special conditions. The docket is available for public inspection before and after the comment closing date. If you wish to review the docket in person, go to the address in the ADDRESSES section of this preamble between 7:30 a.m. and 4 p.m., Monday through Friday, except Federal holidays.

We will consider all comments we receive on or before the closing date for comments. We will consider comments filed late if it is possible to do so without incurring expense or delay. We may change this proposal for special conditions in light of the comments we receive.

If you want the FAA to acknowledge receipt of your comments on this proposal, include with your comments a preaddressed, stamped postcard on which the docket number appears. We will stamp the date on the postcard and mail it back to you.

Background

On November 14, 1996, Airbus Industrie applied for an amendment to U.S. type certificate (TC) A43NM to include the new models A340500 and 600. These models are derivatives of the A340300, which is approved under the same TC.

The Model A340500 fuselage is a 6frame stretch of the Model A340 300 and is powered by 4 Rolls Royce Trent 553 engines, each rated at 53,000 pounds of thrust. The airplane has interior seating arrangements for up to 375 passengers, with a maximum takeoff weight (MTOW) of 820,000 pounds. The Model 340500 is intended for longrange operations and has additional fuel capacity over that of the model A340600.

The Model A340600 fuselage is a 20frame stretch of the Model A340300 and is powered by 4 Rolls Royce Trent 556 engines, each rated at 56,000 pounds of thrust. The airplane has interior seating arrangements for up to 440 passengers, with a MTOW of 804,500 pounds. Type Certification Basis

Under the provisions of 14 CFR 21.101, Airbus Industrie must show that the Model A340500 and 600 airplanes
[[Page 12904]]
meet the applicable provisions of the regulations incorporated by reference in TC A43NM or the applicable regulations in effect on the date of application for the change to the type certificate. The regulations incorporated by reference in the type certificate are commonly referred to as the ``original type certification basis.'' The regulations incorporated by reference in TC A43NM are 14 CFR part 25, effective February 1, 1965, including Amendments 251 through 2563, and Amendments 2564, 2565, 2566, and 2577, with certain exceptions that are not relevant to these proposed special conditions.

In addition, if the regulations incorporated by reference do not provide adequate standards with respect to the change, the applicant must comply with certain regulations in effect on the date of application for the change. The FAA has determined that the Model A340 500 and 600 airplanes must be shown to comply with Amendments 251 through 2591 to part 25, with certain FAAallowed reversions for specific part 25 regulations to the part 25 amendment levels of the original type certification basis.

Airbus has also chosen to comply with part 25 as amended by Amendments 2592, 93, 94, 95, 97, 98, and 104.

If the Administrator finds that the applicable airworthiness regulations (i.e., part 25 as amended) do not contain adequate or appropriate safety standards for the Airbus Industrie Model A340500 and 600 because of a novel or unusual design feature, special conditions are prescribed under the provisions of 14 CFR 21.16.

In addition to the applicable airworthiness regulations and special conditions, the Airbus Industrie Model A340500 and 600 must comply with the fuel vent and exhaust emission requirements of 14 CFR part 34 and the noise certification requirements of 14 CFR part 36.

Special conditions, as defined in 14 CFR 11.19, are issued in accordance with Sec. 11.38 and become part of the type certification basis in accordance with Sec. 21.101(b)(2).

Special conditions are initially applicable to the model for which they are issued. Should the type certificate for that model be amended later to include any other model that incorporates the same novel or unusual design feature, or should any other model already included on the same type certificate be modified to incorporate the same novel or unusual design feature, the special conditions would also apply to the other model under the provisions of Sec. 21.101(a)(1).

Novel or Unusual Design Features

The Airbus Models A340500 and 600 will incorporate the following novel or unusual design feature: a fourwheel center landing gear with braking ability.

Discussion

The basic A340 included a twowheel center landing gear which did not have brakes. The purpose of the center landing gear was to assist the main landing gear during ground handling conditions for heavy airplane weights. This center landing gear was not intended for energy absorption during landing, even if it could participate in the impact under certain conditions. Therefore, to provide additional taxi, takeoff, and landing criteria for this arrangement, Special Conditions 25ANM69 was issued.

The Model A340500 and 600 airplanes have a fourwheel center landing gear which functions in all respects like a main landing gear, including braking capabilities. Because the speeds and weights of the Models A340500 and 600 are greater than that of the basic A340, redesign of the center landing gear was necessary. As a result, the current rules, applying to the original twowheel center landing gear, are inadequate.

Applicability

As discussed above, these special conditions are applicable to the Airbus Models A340500 and 600. Should Airbus Industries apply at a later date for a change to the type certificate to include another model incorporating the same novel or unusual design feature, the special conditions would apply to that model as well under the provisions of Sec. 21.101(a)(1).

Conclusion

This action affects only certain novel or unusual design features of the center landing gear on the Model A340500 and A340600 airplanes. It is not a rule of general applicability, and it affects only the applicant who applied to the FAA for approval of these features on the airplane.

List of Subjects in 14 CFR Part 25

Aircraft, Aviation safety, Reporting and recordkeeping requirements.

The authority citation for these special conditions is as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701, 44702, 44704. The Proposed Special Conditions

Accordingly, the Federal Aviation Administration (FAA) proposes the following special conditions as part of the type certification basis for Airbus Model A340500 and A340600 airplanes.

The following special conditions are proposed in lieu of the previously issued special conditions, ``Ground Load Conditions for Center Landing Gear,'' recorded as item 10 of Special Conditions: Airbus Industrie Model A340 Series Airplanes [Docket No. NM75, Special Conditions No. 25ANM69]:

1. Ground Load Conditions for Center Landing Gear. Notwithstanding Sec. 25.477, the requirements of Sec. 25.473 and Secs. 25.479 through 25.485 apply, except as noted:
(a) In addition to the requirements of Sec. 25.473, ``Landing load conditions and assumptions,'' and Sec. 25.479, ``Level landing conditions,'' landing should be considered on a level runway and on a runway having a convex upward shape that may be approximated by a slope of 1.5 percent at main landing gear stations. The maximum loads determined from these two conditions must be applied to each main landing gear and to the center landing gear.
(b) In addition to the requirements of Sec. 25.483, ``One gear landing conditions,'' the condition represented by Figure 1 also applies:
BILLING CODE 491013P
[[Page 12905]]
[GRAPHIC] [TIFF OMITTED] TP20MR02.005
BILLING CODE 491013P
[[Page 12906]]
(c) In lieu of the requirements of Sec. 25.485, ``Side load conditions,'' the following apply:
(1) The airplane is considered to be in the level attitude with only the main and center wheels contacting the ground.
(2) Vertical reactions of onehalf of the maximum vertical reaction obtained at each main and center gear in the level landing conditions should be considered. The vertical loads must be combined with side loads as follows: for the main gear, 0.8 of the vertical reaction (on one side) acting inward and 0.6 of the vertical reaction (on the other side) acting outward; for the center gear, 0.7 of the vertical reaction acting in the same direction as main gear side loads. These loads are assumed to be applied at the ground contact point and to be resisted by the inertia of the airplane. The drag loads may be assumed to be zero. (d) In addition to Sec. 25.489, ``Ground handling conditions,'' the airplane should be considered to be on a level runway and on a runway having a convex upward shape that may be approximated by a slope of 1.5 percent at main landing gear stations. The ground reactions must be distributed to the individual landing gear units in a rational or conservative manner.
(e) In addition to the requirements of Sec. 25.493(d), ``Braked roll conditions,'' the sudden application of maximum braking effort must be defined taking into account the behavior of the braking system. Failure conditions of the braking system not shown to be extremely improbable must be analyzed in accordance with the following criteria: (1) At the time of occurrence. A realistic scenario, including pilot corrective actions, must be established to determine the loads occurring at the time of failure and immediately after failure. (i) For static strength substantiation, these loads multiplied by an appropriate factor of safety that is related to the probability of occurrence of the failure are ultimate loads to be considered for design. The factor of safety (F.S.) is defined in Figure 2. [GRAPHIC] [TIFF OMITTED] TP20MR02.006
(ii) For residual strength substantiation, the airplane must be able to withstand two thirds of the ultimate loads defined in paragraph (e)(1)(i).
(iii) Failures of the system that result in forced structural vibrations (oscillatory failures) must not produce loads that could result in detrimental deformation of primary structure.
(2) Consideration of certain failure conditions may be required by other sections of part 25, regardless of calculated system reliability. Where analysis shows the probability of these failure conditions to be less than 10⁹, criteria other than those specified in this paragraph may be used for structural substantiation to show continued safe flight and landing.
(3) Warning considerations. For system failure detection and warning, the system must be checked for failure conditions, not extremely improbable, that degrade the structural capability below the level required by part 25 or significantly reduce the reliability of the remaining system. The flightcrew must be made aware of these failures before flight. Certain elements of the control system, such as mechanical and hydraulic components, may use special periodic inspections, and electronic components may use daily checks, in lieu of warning systems to achieve the objective of this requirement. These certification maintenance requirements must be limited to components that are not readily detectable by normal warning systems and where service history shows that inspections will provide an adequate level of safety.
(4) Dispatch with known failure conditions. If the airplane is to be dispatched in a known system failure condition that affects structural
[[Page 12907]]
performance, or affects the reliability of the remaining system to maintain structural performance, then the provisions of these special conditions must be met for the dispatched condition and for subsequent failures. Flight limitations and expected operational limitations may be taken into account in establishing Qj as the combined probability of being in the dispatched failure condition and the subsequent failure condition for the safety margins in Figure 3. These limitations must be such that the probability of being in this combined failure state and then subsequently encountering limit load conditions is extremely improbable. No reduction in these safety margins is allowed if the subsequent system failure rate is greater than 10³ per hour.''
[GRAPHIC] [TIFF OMITTED] TP20MR02.007
Qj = (Tj)(Pj) where:
Tj = Average time spent in failure condition j (in hours). Pj = Probability of occurrence of failure mode j (per hour). (f) In lieu of the requirements of Sec. 25.495, ``Turning,'' the following apply:
(1) The airplane is assumed to execute a steady turn by nose gear steering, or by application of sufficient differential power, so that the limit load factors applied at the center of gravity are 1.0 vertically and 0.5 laterally.
(2) The airplane must be designed for the condition prescribed in paragraph (f)(1), taking into account:
(i) The effects of tire characteristics on the sharing of lateral loads on each tire of the landing gear system, and
(ii) The effect of airframe and landing gear flexibility on the sharing of loads on the different legs of the landing gear system. (g) In lieu of the requirements of Sec. 25.503, ``Pivoting,'' the following apply:
(1) The main and center gear units and supporting structure must be designed for the scrubbing or torsion loads, or both, induced by pivoting during ground maneuvers produced by:
(i) Towing at the nose gear, no brakes applied, and
(ii) Application of symmetrical or unsymmetrical forward thrust to aid pivoting and with or without braking by pilot action on the pedals. (2) The airplane is assumed to be in static equilibrium, with the loads being applied at the ground contact points.
(3) The limit vertical load factor must be 1.0, and:
(i) For wheels with locked brakes applied by pilot action on the pedals, the coefficient of friction must be 0.8.
(ii) For wheels with brakes not applied, the ground tire reactions must be based on reliable tire data.
(4) The failure conditions must be analyzed in accordance with paragraph (e) of these Special Conditions.
(h) In lieu of paragraph (b) of Sec. 25.723 ``Shock absorption tests,'' the center landing gear should not fail in a test demonstrating its reserve energy absorption capacity at design landing weight, assuming airplane lift no greater than the airplane weight acting during a 12feetpersecond airplane landing impact, taking into account both main and center gear acting during the impact. Landing should be considered on a level runway or a runway having a convex upward shape that may be approximated by a slope of 1.5 percent with the horizontal at main landing gear stations, whichever is the most critical.

Issued in Renton, Washington, on February 28, 2002. Vi L. Lipski,
Manager, Transport Airplane Directorate, Aircraft Certification Service.
[FR Doc. 025876 Filed 31902; 8:45 am] BILLING CODE 491013P

FOR FURTHER INFORMATION CONTACT Tim Backman, FAA, ANM-116, Transport Airplane Directorate, Aircraft Certification Service, 1601 Lind Avenue SW., Renton, Washington, 980554056; telephone (425) 2272797; facsimile (425) 2271149.