Browse: Departments   Dates   Agencies  

CFR Citation: 14 CFR Part 23

Docket ID: [Docket No. CE191]; Notice No. 23-03-022-SC]

NOTICE: PROPOSED RULES

ACTION: Airworthiness standards:

DOCUMENT ACTION: Notice of proposed special conditions.

SUBJECT CATEGORY: Special Conditions: Air Tractor Incorporated, Models AT-401, AT- 402, AT-502, AT-602, and AT-802; Seats With Goodrich Aircraft Interior Products (AIP) Four-Point Inflatable Restraints

DATES: Comments must be received on or before January 2, 2003.

DOCUMENT SUMMARY: This notice proposes special conditions for the following Air Tractor AT series airplanes; AT401, AT402, AT502, AT602, and AT 802. These airplanes, as modified by Goodrich Aircraft Interior Products, will have novel and unusual design features associated with a fourpoint inflatable (airbag) restraint. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

SUMMARY: Special conditions—; Air Tractor Inc.,

SUPPLEMENTAL INFORMATION

Interested persons are invited to participate in the making of these proposed special conditions by submitting such written data, views, or arguments, as they may desire. Communications should identify the regulatory docket or notice number and be submitted in duplicate to the address specified above. All communications received on or before the closing date for comments will be considered by the Administrator. The proposals described in this notice may be changed in light of the comments received. All comments received will be available in the Rules Docket for examination by interested persons, both before and after the closing date for comments. A report summarizing each substantive public contact with FAA personnel concerning this rulemaking will be filed in the docket. Persons wishing the FAA to acknowledge receipt of their comments submitted in response to this notice must include with those comments a selfaddressed, stamped postcard on which the following statement is made:
[[Page 71491]]
``Comments to CE191.'' The postcard will be date stamped and returned to the commenter.

Background

On March 8, 2002, Goodrich Aircraft Interior Products (GAIP), 1275 N. Newport Road, Colorado Springs, CO 809162779, applied for a supplemental type certificate to install fourpoint inflatable restraints in Air Tractor AT series airplanes AT401, AT402, AT502, AT602, and AT802. The Air Tractor AT series airplanes comprise a group of agricultural aircraft certificated under 14 Code of Federal Regulations (CFR) 21.25, Restricted Category. These airplanes are intended for single pilot operation, sharing the same seating environment and seattoaircraft attachments. Therefore, the inflatable restraint system proposed by GAIP can be used with each Air Tractor model listed. The inflatable restraint system limits occupant forward excursion in case of an accident, while forming a protective cushion around the sides of the occupant's head. This will reduce the potential for head and torso injury. The inflatable fourpoint restraint behaves in a manner that is similar to an automotive airbag, but in this case, the airbags are integrated into each shoulder harness, inflating away from the occupant. The lapbelt portion of this fourpoint restraint is conventional and does not inflate. While airbags and inflatable restraints are standard in the automotive industry, the use of an inflatable fourpoint restraint is novel for agricultural operations.

Agricultural airplanes, like the Air Tractor AT series, contain many elements of a cashworthy design first described in a 1949 Cornell University study. These elements include a cockpit structure that encases the pilot, crushable structure forward of and underneath the pilot, a lowpositioned instrument panel which the pilot's head would not strike, required use of a helmet, and other features such as a strong harness system and an energy absorbing seat. These design features have contributed to the excellent safety record of agricultural airplanes. The fatality rates experienced by the agricultural airplane fleet are roughly half of that experienced by the general aviation fleet. This lower fatality rate is in spite of a higher overall accident rate with respect to that of general aviation.

In consideration of the excellent fatality record of agricultural airplanes in general, and the Air Tractor AT series in particular, the FAA has determined that installation of a fourpoint inflatable restraint must be accomplished on the basis of not lowering the current level of safety of the AT401, AT402, AT502, AT602, and AT802. Therefore, the FAA considers that installation of an inflatable restraint as having two primary safety concerns:
[sbull] That it perform properly under foreseeable operating conditions, and;
[sbull] That it not perform in a manner or at such times as would constitute a hazard to the airplane or occupants.
The latter point has the potential to be the more rigorous of the requirements. Agricultural operations typically occur at very low altitudes. An unexpected deployment while conducting these operations may result in an unsafe condition in flight. The unexpected deployment may either startle the pilot, or generate a force sufficient to cause a sudden movement of the control stick. Either action could result in a loss of control of the airplane, the consequences of which are magnified due to the low operating altitude. The FAA has considered this when establishing the special conditions.

GAIP has developed a ``Smartbelt'' FourPoint Manually Adjusting Restraint seatbelt with an integrated inflatable airbag device. This inflatable restraint will rely on electronic sensors for firing and pyrotechnic charges for activation. These sensors could be susceptible to inadvertent activation, causing deployment in a potentially unsafe manner. The consequences of an inadvertent deployment must be considered in establishing the reliability of the system. GAIP must substantiate that the effects of an inadvertent deployment in flight are not a hazard to the airplane. In addition, the operating conditions of agricultural aircraft can generate a large amount of cumulative wear and tear on the restraint system. It is likely that the potential for inadvertent deployment increases as a result of this cumulative damage. Therefore, the impact of wear and tear on inadvertent deployment must be considered. Ultimately, because of the effects of this cumulative damage, a life limit must be established for the restraint system design.

There are additional factors to be considered to minimize the chances of inadvertent deployment. Agricultural airplanes are exposed to an extreme operating environment. The effect of this environment on inadvertent deployment of the restraint must be understood. The qualification testing of the firing hardware/software must consider the following:
[sbull] The airplane vibration levels appropriate for agricultural airplanes, and
[sbull] The inertial loads that result from typical flight or ground maneuvers, including gusts and hard landings.
Any tendency for the firing mechanism to activate as a result of these loads or acceleration levels is unacceptable.

Other influences on inadvertent deployment include high intensity electromagnetic fields (HIRF). Since the sensors that trigger deployment are electronic, they must be protected from the effects of this threat. For complying with HIRF requirements, the inflatable system is considered a critical system if its deployment could have a hazardous effect on the airplane; otherwise, it is considered an essential system. Finally, the inflatable restraint should be protected from the effects of fire, so that an additional hazard is not created by, for example, a rupture of the pyrotechnic squib.

While restricted category aircraft need not demonstrate compliance to 14 CFR part 23, Sec. 23.562, there are many elements of Sec. 23.562 that can be used to ensure an adequate level of protection during an emergency landing. These elements include an appropriate crash pulse and various injury pass/fail criteria. Therefore, the inflatable seatbelt must undergo qualification tests of the firing hardware/software for the 26 G deceleration pulse defined under Sec. 23.562(b)(2). When the inflatable portion of the restraint is subjected to, and operates as a result of the 26 G deceleration pulse, it must be shown that deployment of the device will not be a hazard to the occupant. This can be accomplished by assuring that the 4point restraint does not ride above the pelvis into the abdomen, as required by Sec. 23.562(c)(4). This also includes satisfying the maximum harness loads permitted by Sec. 23.562(c)(6).

Given the level of safety of the current Air Tractor harness, the inflatable restraint must show that it will offer an equivalent level of protection in the event the inflatable portion fails to deploy. In the event of an inadvertent deployment, the restraint must still have the same strength capability after the inflatable portion of the restraint has been deployed. There is no requirement for the inflatable portion of the restraint to offer protection during multiple impacts, where more than one impact would require protection.

The inflatable seatbelt system must deploy and provide protection under crash conditions where it is necessary to prevent serious injury. In support of this operational capability, there must be a means to verify the integrity of this system before each flight. As an option, GAIP can establish inspection intervals
[[Page 71492]]
where they have demonstrated the system to be reliable between these intervals.

It is possible a wide range of occupants will use the inflatable restraint. Thus, the protection offered by this restraint should be effective for occupants that range from the fifth percentile female to the ninetyfifth percentile male. In addition, the operation of this restraint must be transparent to the user. Therefore, the design must prevent the inflatable seatbelt from being incorrectly buckled and/or installed such that the airbag would not properly deploy. In addition, when deployment does occur, there must not be a release of hazardous quantities of gas or particulate matter into the cockpit area.

Finally, the inflatable restraint is likely to have a large volume displacement, where the inflated bag could impede the egress of an occupant. Since the bag deflates to absorb energy, it is likely that the inflatable restraint would be deflated at the time an occupant would attempt egress. However, it is appropriate to specify a time interval after which the inflatable restrain may not impede rapid egress. Ten seconds has been chosen as reasonable time. This time limit will offer a level of protection throughout the impact event. Type Certification Basis

Under the provisions of Sec. 21.101, Goodrich Aircraft Interior Products must show that the Air Tractor AT series airplanes AT401, AT 402, AT502, AT602, and AT802, as changed, continue to meet the applicable provisions of the regulations incorporated by reference in Type Certificate No. A17SW (for AT401, AT402, and AT502) and Type Certificate No. A19SW (for AT602 and AT802) or the applicable regulations in effect on the date of application for the change. The regulations incorporated by reference in the type certificate are commonly referred to as the ``original type certification basis.'' The regulations incorporated by reference in Type Certificate No. A17SW are as follows:
[sbull] For models AT401, AT401A, and AT401B, Sec. 21.25(a)(1), 14 CFR part 23 through 239, and Appendix B, CAM 8. For models AT402, AT402A, AT402B, AT502, AT502A, and AT502B, Sec. 21.25(a), (b)(1), (b)(2), Amendments 231 through 239, Appendix B, CAM 8, and additional turbine engine requirements that are of no relevance to the special conditions.

The regulations incorporated by reference in Type Certificate No. A19SW are as follows:
[sbull] For model AT602, 14 CFR part 23 through Amendment 2342. For model AT802, 14 CFR part 23 through Amendment 2342, plus Sec. 21.25(b)(1), (b)(2), and (b)(7). For model AT802A, 14 CFR part 23 through Amendment 42, plus Sec. 21.25(b)(1), (b)(2), and (b)(7). For each model listed above, the certification basis also includes all exemptions, if any; equivalent level of safety findings, if any; and the special conditions adopted by this rulemaking action.

The Administrator has determined that the applicable airworthiness regulations (i.e., part 23 as amended) do not contain adequate or appropriate safety standards for the GAIP inflatable restraint as installed on Air Tractor models AT401, AT402, AT502, AT602, and AT 802 because of a novel or unusual design feature. Therefore, special conditions are prescribed under the provisions of Sec. 21.6.

In addition to the applicable airworthiness regulations and special conditions, Air Tractor models equipped with the GAIP inflatable restraint must comply with the fuel vent and exhaust emission requirements of 14 CFR part 34.

Special conditions, as appropriate, as defined in Sec. 11.19, are issued in accordance with Sec. 11.38, and become part of the type certification basis in accordance with Sec. 21.101(b)(2).

Special conditions are initially applicable to the model for which they are issued. Should the applicant apply for a supplemental type certificate to modify any other model included on the same type certificate to incorporate the same novel or unusual design feature, the special conditions would also apply to that model under the provisions of Sec. 21.101(a)(1).

Novel or Unusual Design Features

Air Tractor Models AT401, AT402, AT502, AT601, and AT802 will incorporate the following novel or unusual design features. The Goodrich Aircraft Interior Products ``Smartbelt'' FourPoint Manually Adjusting Restraint Seatbelt

The purpose of the inflatable airbag seatbelt is to reduce the potential for injury in the event of an accident. In a severe impact, airbags will deploy out of the shoulder harnesses portion of the restraint, in a manner similar to an automotive airbag. These airbags will restrain the motion of the occupant during a severe impact and offer some protection to the head of the occupant. The restraint will rely on electronic sensors for firing, and pyrotechnic charges for activation.

The CFR states performance criteria for seats and restraints in an objective manner. However, none of these criteria are adequate to address the specific issues raised concerning inflatable restraints in agricultural airplanes. Therefore, the FAA has determined that, in addition to the requirements of part 21 and part 23, special conditions are needed to address the installation of inflatable fourpoint restraints.

Accordingly, these special conditions are adopted for Air Tractor Models AT401, AT402, AT502, AT602, and AT802 equipped with the Goodrich Aircraft Interior Products fourpoint inflatable restraint. Other conditions may be developed, as needed, based on further FAA review and discussions with the manufacturer and civil aviation authorities.

The FAA has determined that this project will be accomplished on the basis of not lowering the current level of safety for these Air Tractor models. The FAA recognizes that the current Air Tractor occupant restraint system has an excellent safety record. The FAA has considered the installation of inflatable restraints as having two primary safety concerns: (1) That they perform properly under foreseeable operating conditions; (2) that they not perform in a manner or at such times as would constitute a hazard to the airplane or occupants.

Applicability

As discussed above, these special conditions are applicable to the Air Tractor model series AT401, AT402, AT502, AT602, and AT802 equipped with the GAIP fourpoint inflatable restraint. Should GAIP apply at a later date for a supplemental type certificate to modify any other model on Type Certificate numbers A17SW or AW19SW to incorporate the same novel or unusual design feature, the special conditions would apply to that model as well under the provisions of Sec. 21.101(a)(1). Conclusion

This action affects only certain novel or unusual design features on Air Tractor model series AT401, AT402, AT502, AT602, and AT802 airplanes. It is not a rule of general applicability, and it affects only the applicant who applied to the FAA for approval of these features on the airplane.
List of Subjects in 14 CFR Part 23

Aircraft, Aviation safety, Signs and symbols.
[[Page 71493]]

Citation

The authority citation for these special conditions is as follows:

Authority: 49 U.S.C. 106(g), 40113 and 44701; 14 CFR 21.16 and 21.101 for STC or 21.17 for TC; and 14 CFR 11.38 and 11.19. The Proposed Special Conditions

The FAA has determined that this project will be accomplished on the basis of not lowering the current level of safety for the Air Tractor Model AT401, 402, 502, 602, and 802 series occupant restraint design. Accordingly, the (FAA) proposes the following special conditions as part of the type certification basis for Air Tractor series airplanes AT401, AT402, AT502, AT602, and AT802 modified by Goodrich Aircraft Interior Products.

4Point Inflatable Restraints for Agricultural Airplanes

1. It must be shown that the inflatable seatbelt will deploy and provide protection under crash conditions where it is necessary to prevent serious injury. A dynamic test is required to verify that the system operates as intended when subjected to the 26 G deceleration pulse described in Sec. 23.562(b)(2). The dynamic test need only be performed using a 50 percentile male ATD.

2. The means of protection must take into consideration a range of stature from a 5 percentile female to a 95 percentile male. The inflatable seatbelt must provide a consistent level of energy absorption throughout that range.

3. The design must prevent the inflatable seatbelt from either being incorrectly buckled or incorrectly installed, or both, such that the airbag would not properly deploy.

4. It must be shown that an inadvertent deployment does not cause an unsafe condition (or hazard to the airplane). Consideration needs to be given as a result of wear and tear, or inertial loads resulting from inflight or ground maneuvers (including gusts and hard landings), likely to be experienced in service. The seat belt must have the same strength capability after the inflatable portion of the restraint has been deployed.

5. It must be shown that deployment of the device is not hazardous to the occupant. In addition, the seated occupant must not be injured as established by criteria in Sec. 23.562 as a result of the inflatable seatbelt deployment, including keeping the lap belt located on the pelvis.

6. It must be shown that the inflatable seatbelt will not impede rapid egress of the occupant 10 seconds after its deployment.

7. For the purpose of complying with HIRF and lightning requirements, the inflatable seatbelt system is considered a ``critical system'' if its deployment could have a hazardous effect on the airplane; otherwise, it is considered an ``essential'' system.

8. It must be shown that the inflatable seatbelt will not release hazardous quantities of gas or particulate matter into the cabin.

9. The inflatable seatbelt installation must be protected from the effects of fire such that no hazard to occupants will result.

10. There must be a means to verify the integrity of the inflatable seatbelt activation system before each flight or it must be demonstrated to reliably operate between inspection intervals.

11. A life limit needs to be established for appropriate system designs.

12. Qualification testing of the internal firing mechanism must be accomplished using the vibration levels appropriate for an agricultural airplane.
Michael Gallagher,
Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. 0230325 Filed 112902; 8:45 am]
BILLING CODE 491013M

FOR FURTHER INFORMATION CONTACT Pat Mullen, Federal Aviation Administration, Aircraft Certification Service, Small Airplane Directorate, ACE111, 901 Locust, Kansas City, Missouri, 8163294128, fax 8163294090.