Browse: Departments   Dates   Agencies  

CFR Citation: 14 CFR Part 39

Docket ID: [Docket No. 2002-CE-56-AD]

RIN ID: RIN 2120-AA64

NOTICE: PROPOSED RULES

ACTION: Airworthiness directives:

DOCUMENT ACTION: Notice of proposed rulemaking (NPRM).

SUBJECT CATEGORY: Airworthiness Directives; British Aerospace Model HP.137 Jetstream Mk.1, Jetstream Series 200, Jetstream Series 3101, and Jetstream Model 3201 Airplanes

DATES: The Federal Aviation Administration (FAA) must receive any comments on this proposed rule on or before February 28, 2003.

DOCUMENT SUMMARY: This document proposes to adopt a new airworthiness directive (AD) that would apply to all British Aerospace Model HP.137 Jetstream Mk.1, Jetstream Series 200, Jetstream Series 3101, and Jetstream Model 3201 airplanes. This proposed AD would require you to inspect the steering jack piston rod for cracks and replace if necessary; measure the torque setting of the steering jack piston rod end fitting and stop bolt; and measure the thickness of the tab washers. This proposed AD would also require you to calculate a new safe life limit for the steering jack piston rod based on the results of the proposed inspection and the proposed measurements. This proposed AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for the United Kingdom. The actions specified by this proposed AD are intended to detect, correct, and prevent cracks in the steering jack piston rod, which could result in failure of the steering jack piston rod. Such failure could lead to loss of steering control of the airplane during takeoff, landing, and taxi operations.

SUMMARY: British Aerospace,

SUPPLEMENTAL INFORMATION

How Do I Comment on This Proposed AD?

The FAA invites comments on this proposed rule. You may submit whatever written data, views, or arguments you choose. You need to include the rule's docket number and submit your comments to the address specified under the caption ADDRESSES. We will consider all comments received on or before the closing date. We may amend this proposed rule in light of comments received. Factual information that supports your ideas and suggestions is extremely helpful in evaluating the effectiveness of this proposed AD action and determining whether we need to take additional rulemaking action.
Are There Any Specific Portions of This Proposed AD I Should Pay Attention To?

The FAA specifically invites comments on the overall regulatory, economic, environmental, and energy aspects of this proposed rule that might suggest a need to modify the proposed rule. You may view all comments we receive before and after the closing date of the proposed rule in the Rules Docket. We will file a report in the Rules Docket that summarizes each contact we have with the public that concerns the substantive parts of this proposed AD.

How Can I Be Sure FAA Receives My Comment?

If you want FAA to acknowledge the receipt of your mailed comments, you must include a selfaddressed, stamped postcard. On the postcard, write ``Comments to Docket No. 2002CE56AD.'' We will date stamp and mail the postcard back to you.
Discussion

What Events Have Caused This Proposed AD?

The Civil Aviation Authority (CAA), which is the airworthiness authority for the United Kingdom, recently notified FAA that an unsafe condition may exist on all British Aerospace Model HP.137 Jetstream Mk.1, Jetstream Series 200, Jetstream Series 3101, and Jetstream Model 3201 airplanes. The CAA reports that the steering jack piston rod failed on one of the affected airplanes while in service. The CAA determined that the failure of the piston rod was caused by fatigue cracking on the piston rod end fitting. Fatigue cracking was caused by applying excessive torque to the steering jack piston rod end fitting during assembly.

The safe life limit for the steering jack piston rod is currently 45,000 groundairground (GAG) cycles. Failure of the abovementioned steering jack piston rod occurred at 2,132 GAG cycles. Because of the possibility that excessive torque had been applied to the steering jack piston rod during assembly, the safe life limit for this part has been reduced.
What Are the Consequences If the Condition Is Not Corrected?

This condition, if not detected and corrected, could result in failure of the steering jack piston rod. Such failure could lead to loss of steering control of the airplane during takeoff, landing, and taxi operations.

Is There Service Information That Applies to This Subject?

British Aerospace has issued Jetstream Mandatory Service Bulletin 32JA020741, Original issue: November 2, 2002.
What Are the Provisions of This Service Information? This Service Bulletin Specifies:
Inspecting the steering jack piston rod for cracks and replacing if necessary;
Measuring the torque setting of the steering jack piston rod end fitting and stop bolt;
Measuring the thickness of the tab washers; and

Calculating a new safe life limit for the piston rod.

This service bulletin also references APPH Ltd. Service Bulletin 3276 (pages 1, 2, and 4 through 7, dated October 2002; and page 3, Erratum 1, dated November 2002), which includes procedures for accomplishing the actions specified in British Aerospace Jetstream Mandatory Service Bulletin 32JA020741, Original issue: November 2, 2002.

What Action Did the CAA Take?

The CAA classified these service bulletins as mandatory in order to assure the continued airworthiness of these airplanes in the United Kingdom. The CAA classifying a service bulletin as mandatory is the same in the United Kingdom as the FAA issuing an AD in the United States.
Was This in Accordance With the Bilateral Airworthiness Agreement?

These airplane models are manufactured in the United Kingdom and are type certificated for operation in the United States under the provisions of section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement.

Pursuant to this bilateral airworthiness agreement, the CAA has kept FAA informed of the situation described above.
The FAA's Determination and an Explanation of the Provisions of This Proposed AD

What Has FAA Decided?

The FAA has examined the findings of the CAA; reviewed all available information, including the service information referenced above; and determined that:
The unsafe condition referenced in this document exists or could develop on other British Aerospace Model HP.137 Jetstream Mk.1, Jetstream Series 200, Jetstream Series 3101, and Jetstream Model 3201 airplanes of the same type design that are on the U.S. registry; The actions specified in the previouslyreferenced service
information should be accomplished on the affected airplanes; and AD action should be taken in order to correct this unsafe condition. What Would This Proposed AD Require?

This proposed AD would require you to inspect the steering jack piston rod for cracks and replace if necessary; measure the torque setting of the steering jack piston rod end fitting and
[[Page 3834]]
stop bolt; and measure the thickness of the tab washers. This proposed AD would also require you to calculate a new safe life limit for the steering jack piston rod based on the results of the proposed inspection and the proposed measurements,
Cost Impact

How Many Airplanes Would This Proposed AD Impact?

We estimate that this proposed AD affects 250 airplanes in the U.S. registry.
What Would Be the Cost Impact of This Proposed AD on Owners/Operators of the Affected Airplanes?

We estimate the following costs to accomplish the proposed inspection:
Total cost Labor cost Parts cost per Total Cost on U.S. operators airplane 1 workhour x $60 = $60............... No parts required...... $60 $60 x 250 = $15,000

We estimate the following costs to accomplish any necessary replacements of the steering jack piston rod that would be required based on the results of the proposed inspection and/or measurements. We have no way of determining the number of airplanes that may need such replacement:
Labor cost Parts cost Total cost per airplane 8 workhours X $60 = $240...................... $5,300 $240 + $5,300 = $5,540 Compliance Time of this Proposed AD

What Would Be the Compliance Time of This Proposed AD?

The compliance time of this proposed AD is ``within the next 90 days or 200 groundairground (GAG) cycles after the effective date of this AD, whichever occurs first.''
Why Is the Compliance Time Presented in Calendar Time and Operational Time?

Failure of the steering jack piston rod is only unsafe during airplane operation; this condition is not a result of the number of times the airplane is operated. The cause of the unsafe condition is the result of incorrect torque settings used on the steering jack piston rod end fitting during assembly. We have no way of determining when the unsafe condition occurred on the affected airplanes. For this reason, the FAA has determined that a compliance based on calendar time and operational time should be utilized in this proposed AD in order to assure that the unsafe condition is not allowed to go uncorrected over time.
Regulatory Impact

Would This Proposed AD Impact Various Entities?

The regulations proposed herein would not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this proposed rule would not have federalism implications under Executive Order 13132.
Would This Proposed AD Involve a Significant Rule or Regulatory Action?

For the reasons discussed above, I certify that this proposed action (1) is not a ``significant regulatory action'' under Executive Order 12866; (2) is not a ``significant rule'' under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) if promulgated, will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A copy of the draft regulatory evaluation prepared for this action has been placed in the Rules Docket. A copy of it may be obtained by contacting the Rules Docket at the location provided under the caption ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety. The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration proposes to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. FAA amends Sec. 39.13 by adding a new airworthiness directive (AD) to read as follows:
British Aerospace: Docket No. 2002CE56AD.
(a) What airplanes are affected by this AD? This AD affects Model HP.137 Jetstream Mk.1, Jetstream Series 200, Jetstream Series 3101, and Jetstream Model 3201 airplanes, all serial numbers, that are certificated in any category.
(b) Who must comply with this AD? Anyone who wishes to operate any of the airplanes identified in paragraph (a) of this AD must comply with this AD.
(c) What problem does this AD address? The actions specified by this AD are intended to detect, correct, and prevent cracks in the steering jack piston rod, which could result in failure of the steering jack piston rod. Such failure could lead to loss of steering control of the airplane during takeoff, landing, and taxi operations.
(d) What actions must I accomplish to address this problem? To address this problem, you must accomplish the following:
[[Page 3835]]
Actions Compliance Procedures (1) Insepct the steering Inspect within the In accordance with jack piston rod for cracks. next 90 days or 200 the procedures in (i) If cracks are found, groundairground APPH Ltd. Service replace the cracked (GAG) cycles after Bulletin 3276 steering jack piston rod. the effective date (pages 1, 2, and 4 Install the new steering of this AD, through 7, dated jack piston rod using a whichever occurs October 2002; and torque setting of 175 lbf first. Replace page 3, Erratum 1, (pound force) inch or 20 Nm cracked steering dated November (Newton meters) when jack piston rods or 2002), as tightening the end fitting determine torque referenced in and stop bolt. settings prior to Britich Aerospace (ii) If no cracks are found, further flight. Jetstream Mandatory determine the torque Service Bulletin 32 setting of the steering JA020741, Original jack piston rod end fitting Issue: November 2, and stop bolt.. 2002.
(2) If the torque setting of Prior to further In accordance with the steering jack piston flight after the the procedures in rod end fitting or stop inspection required APPH Ltd. Service bolt is greater than 175 in paragraph (d)(1) Bulletin 3276, lbf inch or 20 Nm and is of this AD. (pages 1, 2, and 4 equal to or les than 435 through 7, dated lbf inch or 49 Nm: October 2002; and (i) Calculate the new safe page 3, Erratum 1, life limit for the steering dated November jack piston rod; and 2002), as (ii) Incorporate the referenced in following into the Aircraft British Aerospace Logbook: ``In accordance Jetstream Mandatory with AD******, the Service Bulletin 32 steering jack piston rod is JA020741, Original life limited to.'' Issue: November 2, 2002.
(3) If the torque setting of Prior to further In accordance with the steering jack piston flight after the the procedures in rod end fitting or stop inspection required APPH Ltd. Service bolt is greater than 435 in paragraph (d)(1) Bulletin 3276, lbf inch or 49 Nm, measure of this AD. (pages 1, 2, and 4 the deformation thickness through 7, dated of the tab washers. October 2002; and (i) If the tab washer page 3, Erratum 1, deformation thickness is dated November greater than 0.001 inch and 2002), as is equal to or less than referenced in 0.005 inch, calculate a new British Aerospace safe life limit for the Jetstream Mandatory steering jack piston rod, Service Bulletin 32 and incorporate the JA020741, Original following into the Aircraft Issue: November 2, Logbook: ``In accordance 2002.
with AD ******, the
steering jack piston rod is
life limited to .''.
(ii) If the tab washer
deformation thickness is
greater than 0.005 inch,
replace the steering jack
piston rod using the torque
settings specified in
paragraph (d)(1) of this
AD..
(4) Do not install any As of the effective In accordance with steering jack piston rod date of this AD. the procedures in unless it has been APPH Ltd. Service inspected, determined to be Bulletin 3276, free of cracks, and the (pages 1, 2, and 4 safe life limit has been through 7, dated established. October 2002; and page 3, Erratum 1, dated November 2002), as referenced in British Aerospace Jetstream Mandatory Service Bulletin 32 JA020741, Original Issue: November 2, 2002.

Note 1: If the owners/operators of the affected airplanes have not kept track of groundairground (GAG) cycles, hours timein service (TIS) may be substituted by calculating 1.5 GAG cycles per hour TIS. For example, 3,000 GAG cycles would equal 2,000 hours TIS. (e) Can I comply with this AD in any other way? You may use an alternative method of compliance or adjust the compliance time if: (1) Your alternative method of compliance provides an equivalent level of safety; and
(2) The Standards Office Manager, Small Airplane Directorate, approves your alternative. Submit your request through an FAA Principal Maintenance Inspector, who may add comments and then send it to the Standards Office Manager.

Note 2: This AD applies to each airplane identified in paragraph (a) of this AD, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/ operator must request approval for an alternative method of compliance in accordance with paragraph (e) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if you have not eliminated the unsafe condition, specific actions you propose to address it.
(f) Where can I get information about any alreadyapproved alternative methods of compliance? Contact Doug Rudolph, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 3294059; facsimile: (816) 3294090.
(g) What if I need to fly the airplane to another location to comply with this AD? The FAA can issue a special flight permit under sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate your airplane to a location where you can accomplish the requirements of this AD.
(h) How do I get copies of the documents referenced in this AD? You may get copies of the documents referenced in this AD from British Aerospace Regional Aircraft, Prestwick International Airport, Ayrshire, KA9 2RW, Scotland; telephone: (01292) 672345; facsimile: (01292) 671625. You may view these documents at FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106.

Note 3: The subject of this AD is addressed in British Aerospace Jetstream Mandatory Service Bulletin 32JA020741, Original Issue: November 2, 2002. This service bulletin is classified as mandatory by the United Kingdom Civil Aviation Authority (CAA).

[[Page 3836]]

Issued in Kansas City, Missouri, on January 15, 2003. Michael Gallagher,
Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. 031677 Filed 12403; 8:45 am]
BILLING CODE 491013P

FOR FURTHER INFORMATION CONTACT Doug Rudolph, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 3294059; facsimile: (816) 3294090.