Browse: Departments Dates Agencies
Docket ID: [Docket No. FAA-2008-0365; Directorate Identifier 2007-NM-274-AD; Amendment 39-15563; AD 2008-12-19]
RIN ID: RIN 2120-AA64
SUBJECT CATEGORY: Airworthiness Directives; Dassault Model Mystere-Falcon 900 and Falcon 900EX Airplanes
The Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD as July 24, 2008.
DOCUMENT SUMMARY: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
This Airworthiness Directive (AD) is issued following the
discovery of a potential chafing between the feeder bundle and the
right side partition wall separating the cabin from the lavatory at
frames 22/23. This chafing may damage the feeder bundle and cause a
sustained smokegenerating shortcircuit between the feeder and the
partition wall made of resistive composite material. Strong smoke
and a difficulttolocalize shortcircuit may result in a hazardous situation.
The unsafe condition is sustained smoke in the cabin, which may lead to
reduced ability of the flightcrew to operate the airplane. We are
issuing this AD to require actions to correct the unsafe condition on
these products.
SUMMARY: Dassault Model Mystere Falcon 900 and Falcon 900EX Airplanes,
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to the specified products. That NPRM was published in the Federal Register on March 31, 2008 (73 FR 16784). That NPRM proposed to correct an unsafe condition for the specified products. The MCAI states:
This Airworthiness Directive (AD) is issued following the
discovery of a potential chafing between the feeder bundle and the
right side partition wall separating the cabin from the lavatory at
frames 22/23. This chafing may damage the feeder bundle and cause a
sustained smokegenerating shortcircuit between the feeder and the
partition wall made of resistive composite material. Strong smoke
and a difficulttolocalize shortcircuit may result in a hazardous situation.
The unsafe condition is sustained smoke in the cabin, which may lead to
reduced ability of the flightcrew to operate the airplane. Corrective
actions include inspecting for damage of the feeder cables, repairing
any damaged feeder cable, installing a protective Teflon tube over the
feeder cable bundle, and modifying the partition wall. You may obtain
further information by examining the MCAI in the AD docket. Comments
We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM or on the determination of the cost to the public.
We reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed.
Differences Between This AD and the MCAI or Service Information
We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.
We might also have required different actions in this AD from those in the MCAI in order to follow our FAA policies. Any such differences are highlighted in a NOTE within the AD.
We estimate that this AD will affect about 38 products of U.S. registry. We also estimate that it will take about 3 workhours per product to comply with the basic requirements of this AD. The average labor rate is $80 per workhour. Required parts will cost about $34 per product. Where the service information lists required parts costs that are covered under warranty, we have assumed that there will be no charge for these parts. As we do not control warranty coverage for affected parties, some parties may incur costs higher than estimated here. Based on these figures, we estimate the cost of this AD to the U.S. operators to be $10,412, or $274 per product.
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ``Subtitle VII: Aviation Programs,'' describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in ``Subtitle VII, Part A, Subpart III, Section 44701: General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this AD:
1. Is not a ``significant regulatory action'' under Executive Order 12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket.
You may examine the AD docket on the Internet at http:// www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains the NPRM, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 6475527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by adding the following new AD:
20081219 Dassault Aviation: Amendment 3915563. Docket No. FAA 20080365; Directorate Identifier 2007NM274AD.
Effective Date
(a) This airworthiness directive (AD) becomes effective July 24, 2008.
Affected ADs
(b) None.
[[Page 34853]]
Applicability
(c) This AD applies to the Dassault airplanes described in
paragraphs (c)(1) and (c)(2) of this AD, certificated in any category.
(1) Model Myst[egrave]reFalcon 900 airplanes, serial numbers
188 through 202 inclusive, except those on which both Dassault Service Bulletins F900358 and F900359 have already been
implemented, or Modification M3891 has already been implemented.
(2) Model Falcon 900EX airplanes, serial numbers 82 through 146
inclusive, except those on which both Dassault Service Bulletins F900EX241 and F900EX251 have already been implemented, or
Modification M3891 has already been implemented.
Subject
(d) Air Transport Association (ATA) of America Code 24: Electrical Power.
Reason
(e) The mandatory continuing airworthiness information (MCAI) states:
This Airworthiness Directive (AD) is issued following the discovery of a potential chafing between the feeder bundle and the right side partition wall separating the cabin from the lavatory at frames 22 / 23. This chafing may damage the feeder bundle and cause a sustained smokegenerating shortcircuit between the feeder and the partition wall made of resistive composite material. Strong smoke and a difficulttolocalize shortcircuit may result in a hazardous situation.
The unsafe condition is sustained smoke in the cabin, which may
lead to reduced ability of the flightcrew to operate the airplane.
Corrective actions include inspecting for damage of the feeder
cables, repairing any damaged feeder cable, installing a protective
Teflon tube over the feeder cable bundle, and modifying the partition wall.
Actions and Compliance
(f) Unless already done, do the following actions.
(1) For Model Myst[egrave]reFalcon 900 airplanes: Do the
actions specified in paragraphs (f)(1)(i) and (f)(1)(ii) of this AD.
(i) Within 330 flight hours or 7 months after the effective date
of this AD, whichever occurs first, inspect for damage of the feeder
cable bundle at the right side partition wall at frames 22/23, and,
if no damage of any feeder cable is found, before further flight,
install a protective Teflon tube over the feeder cable bundle; in
accordance with the Accomplishment Instructions of Dassault Service
Bulletin F900358, Revision 1, dated July 19, 2006. If chafing or
damage of any feeder cable is found, before further flight, repair
the feeder cable in accordance with the Accomplishment Instructions
of Dassault Service Bulletin F900359, Revision 1, dated July 19,
2006; and install a protective Teflon tube over the feeder cable
bundle in accordance with Dassault Service Bulletin F900359,
Revision 1, or Dassault Service Bulletin F900358, Revision 1.
(ii) Within 3,750 flight cycles or 74 months after the effective
date of this AD, whichever occurs first, modify the right side partition wall at frames 22/23; in accordance with the
Accomplishment Instructions of Dassault Service Bulletin F900359,
Revision 1, dated July 19, 2006. Implementation of both Dassault
Service Bulletin F900358 and Dassault Service Bulletin F900359, both Revision 1, both dated July 19, 2006, terminates the
requirements of this AD for Model Myst[egrave]reFalcon 900 airplanes.
(2) For Model Falcon 900EX airplanes: Do the actions specified in paragraphs (f)(2)(i) and (f)(2)(ii) of this AD.
(i) Within 330 flight hours or 7 months after the effective date
of this AD, whichever occurs first, inspect for damage of the feeder
cable bundle at the right side partition wall at frames 22/23, and,
if no such damage of any feeder cable is found, before further
flight, install a protective Teflon tube over the feeder cable
bundle; in accordance with the Accomplishment Instructions of
Dassault Service Bulletin F900EX241, Revision 1, dated July 19,
2006. If any damage of any feeder cable is found, before further flight, repair the feeder cable in accordance with the
Accomplishment Instructions of Dassault Service Bulletin F900EX251,
Revision 1, dated July 19, 2006; and install a protective Teflon
tube over the feeder cable bundle in accordance with Dassault
Service Bulletin F900EX251, Revision 1, or Dassault Service Bulletin F900EX241, Revision 1.
(ii) Within 3,750 flight cycles or 74 months after the effective
date of this AD, whichever occurs first, modify the right side partition wall at frames 22/23, in accordance with the
Accomplishment Instructions of Dassault Service Bulletin F900EX251,
Revision 1, dated July 19, 2006. Implementation of both Dassault
Service Bulletin F900EX241 and Dassault Service Bulletin F900EX
251, both Revision 1, both dated July 19, 2006, terminates the requirements of this AD for Model Falcon 900EX airplanes.
Actions Accomplished According to Previous Issue of Service Bulletin
(g) Actions accomplished before the effective date of this AD,
in accordance with the service information described in Table 1 of
this AD, are considered acceptable for compliance with the corresponding actions specified in this AD.
Table 1.Previous Service Information
Airplane model Dassault service bulletin Date
Falcon 900EX............................. F900EX241.................. October 19, 2005.
Falcon 900EX............................. F900EX251.................. October 19, 2005.
Myst[egrave]reFalcon 900................ F900358.................... October 19, 2005.
Myst[egrave]reFalcon 900................ F900359.................... October 19, 2005. FAA AD Differences
Note: This AD differs from the MCAI and/or service information as follows: No differences.
Other FAA AD Provisions
(h) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Branch, ANM116, FAA, has the authority to approve
AMOCs for this AD, if requested using the procedures found in 14 CFR
39.19. Send information to ATTN: Tom Rodriguez, Aerospace Engineer,
International Branch, ANM116, Transport Airplane Directorate, FAA,
1601 Lind Avenue, SW., Renton, Washington 980573356; telephone
(425) 2271137; fax (425) 2271149. Before using any approved AMOC
on any airplane to which the AMOC applies, notify your appropriate
principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAAapproved. Corrective actions are considered
FAAapproved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in
this AD, under the provisions of the Paperwork Reduction Act, the
Office of Management and Budget (OMB) has approved the information
collection requirements and has assigned OMB Control Number 2120 0056.
Related Information
(i) Refer to MCAI European Aviation Safety Agency (EASA)
Airworthiness Directive 20060270, dated September 4, 2006, and the
service bulletins described in Table 2 of this AD, for related information.
Table 2.Dassault Service Information
Service bulletin Revision Dated
F900EX241......................... 1 July 19, 2006.
F900EX251......................... 1 July 19, 2006.
F900358........................... 1 July 19, 2006.
F900359........................... 1 July 19, 2006. Material Incorporated by Reference
(j) You must use the service information specified in Table 3 of this AD to do the
[[Page 34854]]
actions required by this AD, as applicable, unless the AD specifies otherwise.
(1) The Director of the Federal Register approved the
incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) For service information identified in this AD, contact
Dassault Falcon Jet, P.O. Box 2000, South Hackensack, New Jersey 07606.
(3) You may review copies at the FAA, Transport Airplane
Directorate, 1601 Lind Avenue SW., Renton, Washington; or at the
National Archives and Records Administration (NARA). For information
on the availability of this material at NARA, call (202) 7416030,
or go to: http://www.archives.gov/federalregister/cfr/ibr locations.html.
Table 3.Material Incorporated by Reference
Dassault service bulletin Revision Date
F900EX241......................... 1 July 19, 2006.
F900EX251......................... 1 July 19, 2006.
F900358........................... 1 July 19, 2006.
F900359........................... 1 July 19, 2006.
Issued in Renton, Washington, on June 5, 2008.
Michael J. Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification Service.
[FR Doc. E813589 Filed 61808; 8:45 am]
BILLING CODE 491013P
FOR FURTHER INFORMATION CONTACT Tom Rodriguez, Aerospace Engineer, International Branch, ANM116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 980573356; telephone (425) 2271137; fax (425) 2271149.
14 CFR Part 39 40 CFR Part 52 14 CFR Part 71 33 CFR Part 165 47 CFR Part 73 26 CFR Part 1 50 CFR Part 679 40 CFR Part 180 50 CFR Part 17 33 CFR Part 117 44 CFR Part 67 50 CFR Part 648 14 CFR Part 97 40 CFR Part 63 6 CFR Part 5 33 CFR Part 100 50 CFR Part 622 50 CFR Part 660 26 CFR Part 301 44 CFR Part 65 39 CFR Part 111 40 CFR Part 271 40 CFR Part 300 47 CFR Part 64 40 CFR Parts 52 and 81 50 CFR Part 665 39 CFR Part 3020 50 CFR Part 229 44 CFR Part 64 49 CFR Part 571