Browse: Departments   Dates   Agencies  

CFR Citation: 14 CFR Part 39

Docket ID: [Docket No. FAA-2008-0849; Directorate Identifier 2008-NM-080-AD; Amendment 39-15709; AD 2008-22-13]

RIN ID: RIN 2120-AA64

NOTICE: RULES

ACTION: Airworthiness Directives:

DOCUMENT ACTION: Final rule.

SUBJECT CATEGORY: Airworthiness Directives; Airbus Model A310 Series Airplanes

DATES: This AD becomes effective December 17, 2008.

The Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD as of December 17, 2008.

DOCUMENT SUMMARY: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

Two operators of A300 aircraft fitted with General Electric (GE) CF650 engine series have reported cracks on the lower side of Rib 5 in the pylon box.

* * * * *

Investigations disclosed that these cracks are due to the stresses resulting from the pressure applied by the thrust reverser cowl bumpers.
* * * * *
Cracking of the engine pylons could result in reduced structural integrity of the engine support structure. We are issuing this AD to require actions to correct the unsafe condition on these products.

SUMMARY: Airbus Model A310 Series Airplanes,

SUPPLEMENTAL INFORMATION

We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to the specified products. That NPRM was published in the Federal Register on August 7, 2008 (73 FR 45891). That NPRM proposed to correct an unsafe condition for the specified products. The MCAI states:

Two operators of A300 aircraft fitted with General Electric (GE) CF650 engine series have reported cracks on the lower side of Rib 5 in the pylon box.

The concerned area is similar on A310 aircraft fitted with GE CF680A or CF680C series engines.

Investigations disclosed that these cracks are due to the stresses resulting from the pressure applied by the thrust reverser cowl bumpers.

As a result of the A310 Extended Service Goal (ESG) study, an inspection programme of this area is required by this Airworthiness Directive (AD).

A similar inspection programme is being contemplated for A300 and A300600 series aircraft.
Cracking of the engine pylons could result in reduced structural integrity of the engine support structure. Corrective actions include modifying the Rib 5 in the pylon box. You may obtain further information by examining the MCAI in the AD docket.

Comments

We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM or on the determination of the cost to the public.

Conclusion

We reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed.
Differences Between This AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.

We might also have required different actions in this AD from those in the MCAI in order to follow our FAA policies. Any such differences are highlighted in a Note within the AD.
[[Page 66746]]

Costs of Compliance

We estimate that this AD will affect about 33 products of U.S. registry. We also estimate that it will take about 8 workhours per product to comply with the basic requirements of this AD. The average labor rate is $80 per workhour. Based on these figures, we estimate the cost of this AD to the U.S. operators to be $21,120, or $640 per product.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ``Subtitle VII: Aviation Programs'', describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in ``Subtitle VII, Part A, Subpart III, Section 44701: General requirements''. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this AD:

1. Is not a ``significant regulatory action'' under Executive Order 12866;

2. Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket.

Examining the AD Docket

You may examine the AD docket on the Internet at http:// www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains the NPRM, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 6475527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by adding the following new AD: 20082213 Airbus: Amendment 3915709. Docket No. FAA20080849; Directorate Identifier 2008NM080AD.
Effective Date
(a) This airworthiness directive (AD) becomes effective December 17, 2008.
Affected ADs
(b) None.
Applicability
(c) This AD applies to Airbus Model A310203, 204, and 304 airplanes, all serial numbers, certificated in any category; excluding airplanes that have received Airbus Modification 11110 during production or that have been modified in service in accordance with Airbus Service Bulletin A310542032 (Airbus Modification 11109).
Subject
(d) Air Transport Association (ATA) of America Code 54: Nacelles/Pylons.
Reason
(e) The mandatory continuing airworthiness information (MCAI) states:

Two operators of A300 aircraft fitted with General Electric (GE) CF650 engine series have reported cracks on the lower side of Rib 5 in the pylon box.

The concerned area is similar on A310 aircraft fitted with GE CF680A or CF680C series engines.

Investigations disclosed that these cracks are due to the stresses resulting from the pressure applied by the thrust reverser cowl bumpers.

As a result of the A310 Extended Service Goal (ESG) study, an inspection programme of this area is required by this Airworthiness Directive (AD).

A similar inspection programme is being contemplated for A300 and A300600 series aircraft.
Cracking of the engine pylons could result in reduced structural integrity of the engine support structure. Corrective actions include modifying the Rib 5 in the pylon box.
Actions and Compliance
(f) Unless already done, do the following actions.
(1) Perform a high frequency eddy current (HFEC) inspection and a detailed visual inspection on the lower side of Rib 5 of the left hand and righthand pylons, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A310542036, Revision 02, dated September 28, 2007. Do the inspections at the times specified in paragraph (f)(1)(i) or (f)(1)(ii) of this AD, as applicable.
(i) For Model A310203 and 204 airplanes: Inspect at the later of the times specified in paragraphs (f)(1)(i)(A) and (f)(1)(i)(B) of this AD.
(A) Prior to the accumulation of 40,000 total flight cycles or 60,000 total flight hours, whichever occurs first.
(B) Within 250 flight hours after the effective date of this AD. (ii) For Model A310304 airplanes: Inspect at the later of the times specified in paragraphs (f)(1)(ii)(A) and (f)(1)(ii)(B) of this AD.
(A) Prior to the accumulation of 35,000 total flight cycles or 60,000 total flight hours, whichever occurs first.
(B) Within 250 flight hours after the effective date of this AD. (2) If no crack is found during any inspection required by paragraph (f)(1) of this AD: Repeat the inspections thereafter at intervals not to exceed 15,000 flight hours.
(3) If any crack is found during any inspection required by paragraph (f)(1) of this AD: Before further flight, modify Rib 5 in the pylon box in accordance with the Accomplishment Instructions of Airbus Service Bulletins A310542032, Revision 01, dated October 8, 2007. Accomplishment of this modification ends the repetitive inspections required by this AD.
(4) Accomplishment of the HFEC and detailed visual inspections before the effective date of this AD in accordance with Airbus Service Bulletin A310542036, Revision 01, dated September 14, 1999, meets the corresponding requirements of paragraph (f) of this AD.
(5) Accomplishment of the modification before the effective date of this AD in accordance with Airbus Service Bulletin A310542032, dated May 29, 1996, meets the corresponding requirements of paragraph (f) of this AD.
(6) Submit the initial inspection results specified in Appendix 01 of Airbus Mandatory Service Bulletin A310542036, Revision 02, dated September 28, 2007, at the time specified in paragraph (f)(6)(i) or (f)(6)(ii) of this AD.
(i) If the inspections were done after the effective date of this AD: Within 30 days after accomplishing the inspections required by paragraph (f)(1) of this AD.
[[Page 66747]]
(ii) If the inspections were done prior to the effective date of this AD: Within 30 days after the effective date of this AD. FAA AD Differences

Note: This AD differs from the MCAI and/or service information as follows: Although the MCAI allows further flight after cracks are found during compliance with the required action, this AD requires that you repair the crack(s) before further flight.
Other FAA AD Provisions
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Dan Rodina, Aerospace Engineer,
International Branch, ANM116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 980573356; telephone (425) 2272125; fax (425) 2271149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAAapproved. Corrective actions are considered FAAapproved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120 0056.
Related Information
(h) Refer to MCAI European Aviation Safety Agency (EASA) Airworthiness Directive 20080066, dated March 31, 2008; Airbus Service Bulletin A310542032, Revision 01, dated October 8, 2007; and Airbus Mandatory Service Bulletin A310542036, Revision 02, dated September 28, 2007; for related information.
Material Incorporated by Reference
(i) You must use Airbus Service Bulletin A310542032, Revision 01, dated October 8, 2007; and Airbus Mandatory Service Bulletin A310542036, including Appendix 01, Revision 02, dated September 28, 2007; as applicable; to do the actions required by this AD, unless the AD specifies otherwise.
(1) The Director of the Federal Register approved the
incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) For service information identified in this AD, contact Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 33 33; Internet http://www.airbus.com. (3) You may review copies at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 7416030, or go to: http://www.archives.gov/federal_register/code_of_ federal_regulations/ibr_locations.html.

Issued in Renton, Washington, on October 9, 2008. Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification Service.
[FR Doc. E825767 Filed 111008; 8:45 am]
BILLING CODE 491013P

FOR FURTHER INFORMATION CONTACT Dan Rodina, Aerospace Engineer, International Branch, ANM116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 980573356; telephone (425) 2272125; fax (425) 2271149.